Ultrasonic cleaning machine installation
Please refer to the installation manual of the ultrasonic cleaning machine to connect the temperature control sensor signal line, ultrasonic drive line, heater control line and other lines between the electric control cabinet of the cleaning machine and the host, and install the water supply pipe, discharge pipe and overflow discharge pipe of the cleaning machine.
Placement of Ultrasonic Cleaner Parts
Place the parts in the steel basket and gently put them into the cleaning tank. When there are many parts put in at one time, try to make them evenly distributed in the basket without overlapping.
Turn on the ultrasonic cleaner
When the ultrasonic cleaning machine is working normally, the ultrasonic waves are emitted from three directions at the same time. Push the side ultrasonic to start, and the ultrasonic waves on both sides are already started. Turn the power adjustment knob to the right, push the side ultrasonic to start. And turn it to the appropriate power , The instrument display shows the current ultrasonic working power value.
Ultrasonic cleaner shuts down
If you want to stop during the cleaning process, you should first turn the power knob to the minimum. Press again to stop the bottom ultrasound. The cleaning time depends on the cleaning surface.
Ultrasonic cleaner overflow
If there is too much floating oil on the liquid surface of the cleaning tank, the overflow device of the cleaning machine should be opened to remove it to prevent secondary contamination of the cleaned workpiece. The specific operation is as follows: open the overflow drain valve, pour water or cleaning liquid into the cleaning tank until the cleaning liquid starts to overflow (it is recommended to use a scraper-like appliance to cut the oil slick in the direction of the overflow to promote its rapid flow out), Keep the overflow and discharge valve normally closed to prevent accidental overflow from causing ground pollution.
Ultrasonic cleaning machine post-treatment
Take out the cleaned parts, use compressed air to thoroughly blow out the residual cleaning liquid in each hole, and blow dry the surface (it is recommended to equip a gun with an air compressor). If possible, it is best to configure a pool near the washing machine. In order to rinse the removed parts.
Please refer to the installation manual of the ultrasonic cleaning machine to connect the temperature control sensor signal line, ultrasonic drive line, heater control line and other lines between the electric control cabinet of the cleaning machine and the host, and install the water supply pipe, discharge pipe and overflow discharge pipe of the cleaning machine.
Placement of Ultrasonic Cleaner Parts
Place the parts in the steel basket and gently put them into the cleaning tank. When there are many parts put in at one time, try to make them evenly distributed in the basket without overlapping.
Turn on the ultrasonic cleaner
When the ultrasonic cleaning machine is working normally, the ultrasonic waves are emitted from three directions at the same time. Push the side ultrasonic to start, and the ultrasonic waves on both sides are already started. Turn the power adjustment knob to the right, push the side ultrasonic to start. And turn it to the appropriate power , The instrument display shows the current ultrasonic working power value.
Ultrasonic cleaner shuts down
If you want to stop during the cleaning process, you should first turn the power knob to the minimum. Press again to stop the bottom ultrasound. The cleaning time depends on the cleaning surface.
Ultrasonic cleaner overflow
If there is too much floating oil on the liquid surface of the cleaning tank, the overflow device of the cleaning machine should be opened to remove it to prevent secondary contamination of the cleaned workpiece. The specific operation is as follows: open the overflow drain valve, pour water or cleaning liquid into the cleaning tank until the cleaning liquid starts to overflow (it is recommended to use a scraper-like appliance to cut the oil slick in the direction of the overflow to promote its rapid flow out), Keep the overflow and discharge valve normally closed to prevent accidental overflow from causing ground pollution.
Ultrasonic cleaning machine post-treatment
Take out the cleaned parts, use compressed air to thoroughly blow out the residual cleaning liquid in each hole, and blow dry the surface (it is recommended to equip a gun with an air compressor). If possible, it is best to configure a pool near the washing machine. In order to rinse the removed parts.
Previous：What is the composition and function of ultrasonic plastic welding machine
Next：Already the last article
Add：Room 216, Block B, Innovation and Entrepreneurship Base, No. 213, Huoju Road, Gao District, Weihai 
Support Hotline：0631-5627118 
E-Mail：whhengda@126.com
About Us
Products
News
Mobile Website